Jump to content


Photo

Dyno run

Started by jht , May 11 2007 06:03 pm

  • Please log in to reply
18 replies to this topic

#1 jht

jht

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,769 posts
  • Location:surrey/hants border
  • TDM model: 1996

Posted 11 May 2007 - 06:03 pm

took her finally in for dyno run at Big CC

printout should be attached

K+N, Laser Pro pipes, R1 fuel pump, 160 Mains (dynojet ones), Pilots 2 1/2 turns out, Stock needle setting, FP Emulsion tubes

Rich as f~~k and I'm still getting around 45-47.5 mpg cool.gif

Attached File  TDM_Dyno_run_110507.pdf   375.67KB   396 downloads

Edited by jht, 11 May 2007 - 08:20 pm.

Done: Homo sap navigation/ twisty thing on bars to make it go vroom/ grabby thing to make it stop (in front of twisty thing)/ 'leccy things front and rear to make it glow at night/ Sucky + drippy oiler thing to keep chains moist (!!) / Laser Pro Stock Race pipes / bleeding ear drums (see previous mod)
To do: Educate homo sap nav system to operate twisty + grabby things/ get ear plugs

All Trashed Now... Pants... its a Cat B Mwahahaha it lives again!!


Remember every driver is a deaf myoptic twat who is out to kill you, ALWAYS assume they are going to do THE most f*cking DUMBASS, STUPID manouver possible, at the worst possible moment; get past, and get past quick

#2 jht

jht

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,769 posts
  • Location:surrey/hants border
  • TDM model: 1996

Posted 13 May 2007 - 10:22 am

Toying with jet sizes and came across this, posted several times on a few websites, anyone came across this before?

Gonna call PDQ to get their take on it in the week

http://faq.f650.com/FAQs/JetKitFAQ.htm

http://www.ds650.net...nivsdynojet.htm

http://www.angelfire...vs.dynojet.html


Ever wonder why mikuni and Dynojet Jets have different numbers for the same amount of flow? If yes, then read on to find out why.

Mikuni Dynojet - Main Fuel, Primary and Secondary Pilot Air Jets

Flow rates based on size markings of Mikuni and DynoJet jets are not comparable. As a guide the chart to the left indicates equivalent sizes based on the diameter of hole in the jet.

Mikuni jets are chamfered on the inside opening at the threaded end and Dynojets have a machined flat surface. Keep this in mind when using this chart. These physical differences will never allow an exact comparison.

This chart is intended to be used as a tool to assist you in making a more accurate decision when selecting a jet size range or comparing tuning data where an opposing brand is being used.

Actual jet sizes are highlighted.

DynoJet jets are marked according to the diameter of the hole in the jet .. ie: DJ150 = 1.5mm and DJ175 = 1.75mm.

This is not true for Mikuni or most other OEM equivalent jets. This size Mikuni jet, (N102.221 Super BN), is marked according to its' flow rate, ie: 150 = a rating of 150 cc of fuel per minute.
--------------------------------------------------------------------------------

Mikuni Dynojet
140 149.3
150
142.5 152.0
145 154.7
155
147.5 157.3
150 160
152.5 162.7
165
155 165.3
157.5 168.0
170
160 170.7
162.5 173.3
175
165 176.0
167.5 178.7
180
170 181.3
172.5 184.0
185
175 186.7
177.5 189.3
190
180 192.0
182.5 194.7
195
185 197.3
187.5 200
190 202.7

(copy + pasted info, tried to seperate table above so easier to read, but in aint working..)

Edited by jht, 13 May 2007 - 10:26 am.

Done: Homo sap navigation/ twisty thing on bars to make it go vroom/ grabby thing to make it stop (in front of twisty thing)/ 'leccy things front and rear to make it glow at night/ Sucky + drippy oiler thing to keep chains moist (!!) / Laser Pro Stock Race pipes / bleeding ear drums (see previous mod)
To do: Educate homo sap nav system to operate twisty + grabby things/ get ear plugs

All Trashed Now... Pants... its a Cat B Mwahahaha it lives again!!


Remember every driver is a deaf myoptic twat who is out to kill you, ALWAYS assume they are going to do THE most f*cking DUMBASS, STUPID manouver possible, at the worst possible moment; get past, and get past quick

#3 Guest_GuyGraham_*

Guest_GuyGraham_*
  • Guests

Posted 02 July 2007 - 11:40 am

QUOTE(jht @ Sun 13th May 2007, 11:07 AM) <{POST_SNAPBACK}>
Toying with jet sizes and came across this, posted several times on a few websites, anyone came across this before?

Gonna call PDQ to get their take on it in the week

http://faq.f650.com/FAQs/JetKitFAQ.htm

http://www.ds650.net...nivsdynojet.htm

http://www.angelfire...vs.dynojet.html


Ever wonder why mikuni and Dynojet Jets have different numbers for the same amount of flow? If yes, then read on to find out why.

Mikuni Dynojet - Main Fuel, Primary and Secondary Pilot Air Jets

Flow rates based on size markings of Mikuni and DynoJet jets are not comparable. As a guide the chart to the left indicates equivalent sizes based on the diameter of hole in the jet.

Mikuni jets are chamfered on the inside opening at the threaded end and Dynojets have a machined flat surface. Keep this in mind when using this chart. These physical differences will never allow an exact comparison.

This chart is intended to be used as a tool to assist you in making a more accurate decision when selecting a jet size range or comparing tuning data where an opposing brand is being used.

Actual jet sizes are highlighted.

DynoJet jets are marked according to the diameter of the hole in the jet .. ie: DJ150 = 1.5mm and DJ175 = 1.75mm.

This is not true for Mikuni or most other OEM equivalent jets. This size Mikuni jet, (N102.221 Super BN), is marked according to its' flow rate, ie: 150 = a rating of 150 cc of fuel per minute.
--------------------------------------------------------------------------------

Mikuni Dynojet
140 149.3
150
142.5 152.0
145 154.7
155
147.5 157.3
150 160
152.5 162.7
165
155 165.3
157.5 168.0
170
160 170.7
162.5 173.3
175
165 176.0
167.5 178.7
180
170 181.3
172.5 184.0
185
175 186.7
177.5 189.3
190
180 192.0
182.5 194.7
195
185 197.3
187.5 200
190 202.7

(copy + pasted info, tried to seperate table above so easier to read, but in aint working..)



not strictly true
there are two types of mikuni jets - hex head and screwdriver slot

the ones with a screwdriver slot are numbered in the dia of the hole, the hex main jets are flow rate.

It has been proven on Thmpetalk that Mikuni and DJ jets are the same.
Do not believe what DJ tell you - they are in the market to make money from selling their jets.

#4 TonyDevil

TonyDevil

    seagull squadron leader & founding member of GoatTracKrew

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 9,336 posts
  • Location:Saarfend-on-Sea, Essex
  • TDM model: 1991

Posted 24 September 2008 - 06:43 pm

been messing around with carb tuning and couldnt find this info anywhere
was down at PDQ today and they did a photo copy for me good.gif




and then JHT taught me how to balance carbs wink.gif
they werent great, but sorted now yahoo.gif

"Never argue with an idiot. They just bring you down to their level and beat you with experience"
My TDM :
Black 1991 850 MK1, 160k+ miles(ish, best guess really, gave up trying to keep count after 3rd set of clocks and 3rd engine), PilotRoad2 tyres, custom stubby exhaust system, bluespot calipers & goodridge braided hoses with dunlopads, maxton forks, Ohlins shock, kedo handguards, stainless TDM grill, Scottoiler with lubetube & dual nozzle thingy, Givi Wingrack2 with E45 & 2xE36s, renntec crash bars, Autocom with blueteeth & PMR radio, TomTom Rider2, Optimate IIIsp, Bagster tank cover, anti-dazzle coating
to fit : led spotlights, heated grips, new braided lines and rear caliper that actually has bleed nipples
Silver-ish 2003 900, 70k miles, PilotRoad3 front tyre (new@65k) & PR2 rear(new at 69k), Renthal 755 bars with KTM handguards, oxford unheated grips, power commander 3usb, scorpion titanium exhausts, standard screen with vario winglet thingy, stainless grill, oem centre stand, bagster tank cover, givi monokey topplate mounted on grabrail with V46 topbox, Givi PL pannier rails with E21s, crash bungs, mirror extender thingys, Halfords Advanced Laser Blue brillance bulbs, 21w led spotlights, touring scottoiler with leehenty dual nozzle, Autocom with blueteeth & PMR radio, TomTom Rider3 Urban, winter style anti-dazzle coating
to fit : led brake light strip, replacement heated grips
current rides : TDM850 3vd/mk1=tourer&scratcher, TRX850=weekend twisty toy, 2003 TDM900=commuter, 2005 TDM900=unmolested.  Gone but not forgotton : XTZ750=overland touring toy, GS500e, GS125
If a strange looking truck driver honks at you & gives you the thumbs up, its could be me  :good:

#5 chill

chill

    Carpe fan

  • Member
  • Pip
  • 151 posts
  • Location:Brisbane Australia
  • TDM model: 2002

Posted 17 November 2009 - 01:10 am

I final had a dino check done on mine today.
model 2002 with 60000 km, only done the air box mod and running a 170x60 rear tyre.
One up I average 22/23 km/lt (on a quiet run up to 25). Two up and loaded 19/20

When I can figure how to add picture I will but for now.

Figures are Hp = 71.72
Torque = 56.13

#6 jht

jht

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,769 posts
  • Location:surrey/hants border
  • TDM model: 1996

Posted 23 June 2012 - 10:18 am

Recent run as need to get arond to leaning of the top end (only 5 years later!)

Used Dyntoech over near Tadley, nice bunch of bloke who definitely knew their onions

Since 1st run back in 2007, have had top end rebuild with relapped valves & new stem seals, honed bore & rings (all about 6-8k miles ago)

76.93bhp, 61.4 ft/lb torque



Edited by jht, 23 June 2012 - 10:33 am.

Done: Homo sap navigation/ twisty thing on bars to make it go vroom/ grabby thing to make it stop (in front of twisty thing)/ 'leccy things front and rear to make it glow at night/ Sucky + drippy oiler thing to keep chains moist (!!) / Laser Pro Stock Race pipes / bleeding ear drums (see previous mod)
To do: Educate homo sap nav system to operate twisty + grabby things/ get ear plugs

All Trashed Now... Pants... its a Cat B Mwahahaha it lives again!!


Remember every driver is a deaf myoptic twat who is out to kill you, ALWAYS assume they are going to do THE most f*cking DUMBASS, STUPID manouver possible, at the worst possible moment; get past, and get past quick

#7 Studley Ramrod

Studley Ramrod

    Monkey Boys Monkey

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 19,268 posts
  • Location:HELLO ! I'm in the Library...Notts
  • TDM model: 1993

Posted 23 June 2012 - 10:43 am


That's healthy ! smile.gif

Do you think it's the pro stocks that are leaning out the top end ? unsure.gif

Mk2a 2000 in Silver. Top end Refurb @ 41100 miles, Scottoiler, Renthal Road High Bars, Up & Back Bar Risers, Bellypan, DL650 Handguards, Capt. Picard Bar Ends, House of Henty SS Wheel spacers, New Seat Cover Fitted. 58 MPG !!  Now owned by chrisbee !   Studley's mk2a Bloggerydoodaah !  Photos of my first MK1  Photos of my MK2a  TPLQHCSRSFC No. 1 Fan

#8 jht

jht

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,769 posts
  • Location:surrey/hants border
  • TDM model: 1996

Posted 23 June 2012 - 05:13 pm

She ain't lean at the top Studders, she be tad rich tongue.gif
13:1 is kinda optimal A/F ratio, from 5k up she gets progressively richer
The lean dip around 3-4k is on the needle & more likely than not leaning out for emissions/noise test
Done: Homo sap navigation/ twisty thing on bars to make it go vroom/ grabby thing to make it stop (in front of twisty thing)/ 'leccy things front and rear to make it glow at night/ Sucky + drippy oiler thing to keep chains moist (!!) / Laser Pro Stock Race pipes / bleeding ear drums (see previous mod)
To do: Educate homo sap nav system to operate twisty + grabby things/ get ear plugs

All Trashed Now... Pants... its a Cat B Mwahahaha it lives again!!


Remember every driver is a deaf myoptic twat who is out to kill you, ALWAYS assume they are going to do THE most f*cking DUMBASS, STUPID manouver possible, at the worst possible moment; get past, and get past quick

#9 Studley Ramrod

Studley Ramrod

    Monkey Boys Monkey

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 19,268 posts
  • Location:HELLO ! I'm in the Library...Notts
  • TDM model: 1993

Posted 23 June 2012 - 06:10 pm


Hahaaa ! yes, cough cough ! Of course I knew that, errrr, just testing you bod ! blush.gif

Mk2a 2000 in Silver. Top end Refurb @ 41100 miles, Scottoiler, Renthal Road High Bars, Up & Back Bar Risers, Bellypan, DL650 Handguards, Capt. Picard Bar Ends, House of Henty SS Wheel spacers, New Seat Cover Fitted. 58 MPG !!  Now owned by chrisbee !   Studley's mk2a Bloggerydoodaah !  Photos of my first MK1  Photos of my MK2a  TPLQHCSRSFC No. 1 Fan

#10 jht

jht

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,769 posts
  • Location:surrey/hants border
  • TDM model: 1996

Posted 23 June 2012 - 06:23 pm

S'all right, yesterday I had a serious brain fart discussing the jetting and told Saga optimal A/F was around 11:1
rolleyes.gif
Done: Homo sap navigation/ twisty thing on bars to make it go vroom/ grabby thing to make it stop (in front of twisty thing)/ 'leccy things front and rear to make it glow at night/ Sucky + drippy oiler thing to keep chains moist (!!) / Laser Pro Stock Race pipes / bleeding ear drums (see previous mod)
To do: Educate homo sap nav system to operate twisty + grabby things/ get ear plugs

All Trashed Now... Pants... its a Cat B Mwahahaha it lives again!!


Remember every driver is a deaf myoptic twat who is out to kill you, ALWAYS assume they are going to do THE most f*cking DUMBASS, STUPID manouver possible, at the worst possible moment; get past, and get past quick

#11 Rallyist

Rallyist

    Gettin to be an 'Old Bugger'

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 3,258 posts
  • Location:Usually in a Hospital somewhere in the Birmingham area
  • TDM model: 1993

Posted 23 June 2012 - 06:41 pm

QUOTE(jht @ Sat 23rd Jun 2012, 06:13 PM) <{POST_SNAPBACK}>
She ain't lean at the top Studders, she be tad rich tongue.gif
13:1 is kinda optimal A/F ratio, from 5k up she gets progressively richer
The lean dip around 3-4k is on the needle & more likely than not leaning out for emissions/noise test



Could probably go down 1 size on main jet then run again as it looks like slide/needle may need fine tuning.

For a challenging summer try the

Round Britain Rally.....  




1993 TDM 850 Mk1 ..... 2008 TDM 900 ....  1975, 1979, 1982, 1992 Goldwings, Scott, AJS,  Triumph 5TA

#12 palexxxx

palexxxx

    enuff posts to fill a 50cc

  • Member
  • 53 posts
  • Location:Hervey Bay, Qld, Australia
  • TDM model: 2002

Posted 21 December 2013 - 08:25 am

Correct air/fuel ratio is 14.7 (or so I'm told).


#13 dandywarhol

dandywarhol

    Carpe Citizen

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 5,324 posts
  • Location:Edinburgh, Scotland
  • TDM model: 2003

Posted 21 December 2013 - 01:52 pm

14.7 by weight, around 30,000:1 by volume.

 

That graph fuelling looks ok to me for a full throttle application


1967 Yamaha TD1C 250, 2014 Kawasaki W800, 2011 Aprilia Tuono 1000 V4, 2020 Yamaha XSR900

"At the cutting edge of technophobia" Scotland_180-animated-flag-gifs.gif mccoy.gif
 

#14 ZeevGutkin

ZeevGutkin

    arrived on last train

  • Member
  • 2 posts
  • Location:Israel
  • TDM model: 2005

Posted 06 March 2014 - 12:43 pm

Hi,

This is all very interesting.

I was wondering (and this may sound stupid...), do you have any experience with fitting a post 1999 carb (4TX4 40) onto a TDM 900 motor?

I'm asking because I've got the 900 motor fitted on my XTZ frame and the post 1999 carbs.

I get backfires from the exhaust when decelerating from high revs (>4000) at around 3000 - 3500.

I read somewhere that these backfires from the exhaust are a result of the mixture being to lean to fire in the cylinder and get ignited in the exhaust by the hot gases from a following stroke that does ignite.

In did when I pull the choke while decelerating from high revs, there are no backfires.

So far I've replaced the pilot air gets (2 of them on this carbs). The 120 is now 105 and the 87.5 is now 45 - yes it's better now, but I still have the occasional explosion at the rear end.

Any advice will be highly appreciated. 

Thanks.

Zeev.


#15 palexxxx

palexxxx

    enuff posts to fill a 50cc

  • Member
  • 53 posts
  • Location:Hervey Bay, Qld, Australia
  • TDM model: 2002

Posted 06 March 2014 - 01:24 pm

Why would you fit carbs to an engine that has fuel injection on it as standard?  Seems to me like you want to go backwards in time.  Perhaps going from the Intercity 125 (or whatever the modern equivelant is (I haven't been in England in a long,  long time))  to going to steam.


#16 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 06 March 2014 - 01:45 pm

Things loike wiring and not getting your necked snapped off with terrible jerky/lumpyness in throttle response?  Carb for me anytime ta.

 

Zeev, I vaguely remember a post on ear of someone who put carbs on their 900 but dont have linky dink... EDIT: do have linky dink: http://www.carpe-tdm...&hl=anda&page=5


"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#17 wicklamulla

wicklamulla

    is it Jizzy Rascal time yet.....?

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 12,211 posts
  • Location:Parish of Cruwys (pronounced 'Cruise' just loike Tom) Morchard, Mid Devon.
  • TDM model: 1999

Posted 06 March 2014 - 02:42 pm

It'd be too much messing around with the efi to get it to run properly on an old super tenere.    carbs are the way forward!


spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.

I loike tay and hang sangwiches !

www.kenhogantreeservices.co.uk

http://s33.photobuck...77/wickla/?sc=6



http://reg.imageshack.us/v_images.php

post-1-1150550733.gifpost-1-1150550726.gifpost-1-1150559830.gif

#18 Studley Ramrod

Studley Ramrod

    Monkey Boys Monkey

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 19,268 posts
  • Location:HELLO ! I'm in the Library...Notts
  • TDM model: 1993

Posted 07 March 2014 - 11:05 am

Also less electrickery to go tits up when you use carbs. :D

 

Regarding the backfire, both my mk1 and mk2a kind of backfired when decellerating and I'm wondering if you're actually getting a proper backfire as in an almighty bang, or just the smaller more frequent farty ones like my bikes did.

 

I believe the air cutoff valves on the carbs are there to help stop backfiring so maybe have a look to see if they're damaged/perforated ?

 

The 3-4000rpm range generally concerns the emulsion tubes and needle height.

 

I dunno if this CV Carb tuning guide might help you.  http://www.factorypr...pm_engines.html


Mk2a 2000 in Silver. Top end Refurb @ 41100 miles, Scottoiler, Renthal Road High Bars, Up & Back Bar Risers, Bellypan, DL650 Handguards, Capt. Picard Bar Ends, House of Henty SS Wheel spacers, New Seat Cover Fitted. 58 MPG !!  Now owned by chrisbee !   Studley's mk2a Bloggerydoodaah !  Photos of my first MK1  Photos of my MK2a  TPLQHCSRSFC No. 1 Fan

#19 harvey krumpet

harvey krumpet

    full o shoite

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 2,059 posts
  • Location:New Zealand
  • TDM model: 1997

Posted 09 March 2014 - 08:44 am

Also less electrickery to go tits up when you use carbs. :D

 

Regarding the backfire, both my mk1 and mk2a kind of backfired when decellerating and I'm wondering if you're actually getting a proper backfire as in an almighty bang, or just the smaller more frequent farty ones like my bikes did.

 

I believe the air cutoff valves on the carbs are there to help stop backfiring so maybe have a look to see if they're damaged/perforated ?

 

The 3-4000rpm range generally concerns the emulsion tubes and needle height.

 

I dunno if this CV Carb tuning guide might help you.  http://www.factorypr...pm_engines.html

Hmmm, mine has started nasty botty burps on occasion when I come back to idle after currying it. Fresh mulching tubes about 10'000k ago sorted the last bout of biliousness. Will add that cut off valve to the check list of things when it goes in for a top end service. Ta Studley.

The bike has pretty much open pipes which I'm sure exacerbate any carb issues.


TDM 850 Loud and unusual. CRM 250r Woo hoo! DT 230 Lanza Fiddled with.... Bloody hell, is that legal? GG Randonee AKA "I didn't think that was possible".

Back to Engine, Fluids & Exhausts

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

  1. Carpe TDM
  2. → Start your Engine
  3. → KnowledgeBase
  4. → Engine, Fluids & Exhausts
  5. Privacy Policy