Jump to content


Photo

Fork Oil Seal (mkI)


  • Please log in to reply
168 replies to this topic

#1 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 11 June 2006 - 05:51 pm

Grrr if I jounce my forks there is a residue on the LHS fork slider that smells alot like pickled onion water! If I wipe this away and jounce again, there is less residue. If I do it for a third time its dry!!!!!!

Anyone know what causes this? I would hate to tek the forks apart if there is not really a leak, but would also hate to leave em and spring a proper leak whilst on travels!!!

Someone posted a linky dink to a kit with new sloiders and oil..........anyone know where that is?

Boop
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#2 wicklamulla

wicklamulla

    is it Jizzy Rascal time yet.....?

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 12,211 posts
  • Location:Parish of Cruwys (pronounced 'Cruise' just loike Tom) Morchard, Mid Devon.
  • TDM model: 1999

Posted 11 June 2006 - 07:41 pm

lift/slide up the dust cover and have a peak to see if any of that oil ya spilt is sitting there, what ever ya find wipe/wash it away and then jump up and doon on the fecker 2c if pickled onion water returns.

spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.

I loike tay and hang sangwiches !

www.kenhogantreeservices.co.uk

http://s33.photobuck...77/wickla/?sc=6



http://reg.imageshack.us/v_images.php

post-1-1150550733.gifpost-1-1150550726.gifpost-1-1150559830.gif


#3 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 11 June 2006 - 08:31 pm

Good plan Wicky, gonna go and try that noooo.

I know how this is gonna work...the day afore RTT, the seal will let go proper and oil be burgered.

Lucky when I picked up one of me mkI garden ornament enjuns from Pantaloonie he give oi a set o forks too........so gonna rebuild them bassads just incase, here's where we is at so far this eve: Attached File  POW1.jpg   62.29KB   197 downloads



Do these fork seals seem a good price on ebay? http://cgi.ebay.co.u...1QQcmdZViewItem

Boop
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#4 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 11 June 2006 - 09:59 pm

QUOTE(wicklamulla @ Sun 11th Jun 2006, 08:26 PM) <{POST_SNAPBACK}>
lift/slide up the dust cover and have a peak to see if any of that oil ya spilt is sitting there



This def aint spilt oil...its pickled onion water oi can smell the bassad.

Have bought a couple of sets of them thur seals off ebay.

Any suggestions for cheap/effective method of paint for front fork sloiders? I cant be arsed to Stove Enamel and was thunkin of just some satin finish Hammerite?

Boop
dapleb.
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#5 unclesumo

unclesumo

    Carpe Regular

  • Member
  • Pip
  • 140 posts
  • Location:Teesside
  • TDM model: 1998

Posted 12 June 2006 - 05:39 am

Ya could try painting them with steel wheel paint, I painted some car carbs with it once & looked pretty good.

#6 wicklamulla

wicklamulla

    is it Jizzy Rascal time yet.....?

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 12,211 posts
  • Location:Parish of Cruwys (pronounced 'Cruise' just loike Tom) Morchard, Mid Devon.
  • TDM model: 1999

Posted 12 June 2006 - 08:23 am

QUOTE(unclesumo @ Mon 12th Jun 2006, 06:24 AM) <{POST_SNAPBACK}>
Ya could try painting them with steel wheel paint, I painted some car carbs with it once & looked pretty good.



agree with Sumo.


PK i would only use Genuine yam fork seals arrrrrrrr arrrrrrrrr arrrrrrrrr, reason being i once fitted spurious ones to an LC on a sat, the following wed i had to change em again with genuine yam wans.............. ranting.gif while yer at it are ya gonna rub doon the pitted/rusty chrome bits and have em rechromed or go down the araldite route????

spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.

I loike tay and hang sangwiches !

www.kenhogantreeservices.co.uk

http://s33.photobuck...77/wickla/?sc=6



http://reg.imageshack.us/v_images.php

post-1-1150550733.gifpost-1-1150550726.gifpost-1-1150559830.gif


#7 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 12 June 2006 - 05:00 pm

Yeah I ordered two sets of the ebay seals (argh arrgggh argggghhh).....but seeing as I don't have much time to play with now, I also ordered a set from Damerells (and also top/bottom bushes as the teflon ripped off them when the forks were seperated, as Stinky mentioned). Also Haynes mentions the the top bush CAN'T "pass through" the bottom bush....so when you pull apart, all the components (seal/washer/top bush) come out of the slider at the same time on the end of the fork tube........they lie.

Didnt have time to look at paint today. Have never heard of steel wheel paint, will pop into local auto place and see if they gots any, thanks for the tippola.

EDIT: I wont do anything with fork tube chrome....they are pitted on Pantaloonies set but not as bad as the ones on there. The seal thats gone? is on the leg where the chrome is fine!!! Go figure.....I jounced again today and no residue blink.gif blink.gif , they are gettin changed now anyway....work send them away and get em rechromed for £30 a leg, but it takes months to get em back.......gonna just rebuild as is....and then rebuild the ones that come off a bit more leisurely like.

Boop
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#8 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 12 June 2006 - 07:31 pm

Haynes: "Install the oil seal washer with its flat side facing up" ......thats odd cos mine are both flat side facing doon....anyone know if Haynes is right or mine are right? Woud seem logical to have flat section facin doon to seaton top bush? I ruh roh!

Boop
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#9 Stink-Foot

Stink-Foot

    Carpe fan

  • Members
  • Pip
  • 152 posts
  • Location:Helsinki, Finland
  • TDM model: 1995

Posted 13 June 2006 - 04:53 pm

QUOTE(dapleb @ Mon 12th Jun 2006, 09:16 PM) <{POST_SNAPBACK}>
Haynes: "Install the oil seal washer with its flat side facing up" ......thats odd cos mine are both flat side facing doon....anyone know if Haynes is right or mine are right? Woud seem logical to have flat section facin doon to seaton top bush? I ruh roh!

Boop
dapleb


I was puzzled about that washer myself when I did mine. Like You, I thought the flat side should face down. Mine were as per Haynes's instructions and I installed them in the same way, flat side up. They seem to work fine so I guess they'll be fine either way.

If You need new fork chrome tubes KEDO sells them at around 100EUR each. Excellent quality made by Wilbers. I bought a pair when I dropped my bike and bent the tubes a few years ago.

Don't go painting and polishing your ride! Just keep it mechanically solid. It's great to humiliate crotch rocket posers with a bike that looks like it's just been run over by a truck...
Beat Your dick like it owes You money.

#10 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 13 June 2006 - 05:20 pm

Thanks for the washer and Kedo info Stinky. I will try them flat side up as these forks have obviously been apart before (nice gouges by the seal seat).

Spoke to the Bentley boys and they recommended that I strip the sliders, use etching primer and then a standard (stain black) finish paint, 4 thin coats leaving 15mins drying time inbetween.

Scruffy but mechanically sound is def the way to go Stinky good.gif

Cheers
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#11 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 16 June 2006 - 04:24 pm

Anyone got advice on how to drive the top bush into its housing in the sloider please?

Haynes seems a little conufsed as it talks about a long drift bigger than the fork tube but smaller than the recess for the bush....and next its on about installing the washer and using that as a surface to drive on.

Cheers
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#12 Stink-Foot

Stink-Foot

    Carpe fan

  • Members
  • Pip
  • 152 posts
  • Location:Helsinki, Finland
  • TDM model: 1995

Posted 16 June 2006 - 06:21 pm

QUOTE(dapleb @ Fri 16th Jun 2006, 06:09 PM) <{POST_SNAPBACK}>
Anyone got advice on how to drive the top bush into its housing in the sloider please?


First I protected the chromed fork legs with masking tape. Then I used the old bush and a small drift to drive the new bush in to it's housing. Gently tapping on the old bush pushed the new one in easily. Slightly oiling the bush made it a lot easier.

Similarly old fork seals were useful when installing new ones. Make sure the forks are fully compressed when installing new bushed and seals so any possible damage wont be in the critical areas of the fork tubes. Protecting the drift with tape or something might be wise too.
Beat Your dick like it owes You money.

#13 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 16 June 2006 - 07:08 pm

Thanks Stinky. I was hoping that because the bushes slotted they wouldnt be too hard to drift into place. Was planning on using a foot long section of poipe, but may well try the 'Stinky method' now...thanks.

I have been trying to work out what could be done differently to save the bushes from destruction when dismantling but I think its inevitable!

Cheers
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#14 Tom S

Tom S

    enuff posts to fill a 50cc

  • Member
  • 55 posts
  • Location:Anchorage Alaska
  • TDM model: 1992

Posted 19 June 2006 - 05:47 am

Hi guys! At last I have got into this forum! Took a long time, but I think I got here just in time.
I did not see anywhere to post an intro here so I guess this is it for now.
I need to change a fork seal on my '92 TDM 850. From what I read above by Mr Stink Foot, it sounds like I may need more parts.
This looks like it might be more of a pain than doing the Buell fork that I just finished.
I have the factory service manual but do not think highly of it. Most of the pix look like bad, dark, xerox copies. But it has got to be better than Haynes.
I am hoping that I can do this without destroying those teflon coatings on the bushes, as mentioned above.

Question 1:
I assume these are the bushings. Part #'s 14 & 16 in this pic?


I did find this:
http://www.carpe-tdm...findpost&p=6164
I will have to read through that a couple times again.

Question 2:
Can I use this method to change the seal without damaging the bushes?

Question 3: Special tools, I think I can fabricate what I need, but not sure what they really look like. The rod holder/puller just looks like a thin spanner. Should be easy to make. Made my own seal driver for the Buell fork. Made other tools too.
Anyone have any good pix of fork parts/ special tools?

Sorry to come on here with a bunch of questions right off, but riding season is about 6 months here & I am needy.
If I can get some help, or be directed to somewhere on this site I would really appreciate it & do my best to give what pay back I can over the net.

I have one of the few TDM's in Alaska. Maybe the only one. Have never seen another. There was one about 200 miles from here but I heard it was sold and went "outside". A term us old Alaskans use. That is anyplace outside Alaska. Mostly the lesser 48 states.

Here is the TDM. Bought used in '01, & it is still pretty much like I bought it.


Me on the Buell with Mad Max's dog. Dog makes the pic. : )


Might as well toss in this one. Moose in back yard, somebody photochopped in the bike for me. I drilled a lot of holes in that Buell.
It is a lot lighter than the TDM. 385 lb / 174.63 kilos with 1/2 tank of, em, er, -- petrol.


Please--- HELP!!

Edited by Tom S, 19 June 2006 - 10:20 am.


#15 Tom S

Tom S

    enuff posts to fill a 50cc

  • Member
  • 55 posts
  • Location:Anchorage Alaska
  • TDM model: 1992

Posted 19 June 2006 - 10:03 am

Still begging. Went back & PM'ed 'Plug' as per following.
Hope this does not double post like it just did.
Dammick! Reversed them maybe ok now.
Where is that 'old' site?
Anxious in Anchorage
tom3ATgci.net
blink.gif
**********************
Plug, I find that I am in the same boat as you were. Can you help? How did you get the seal out. Can you be more specific? Just dig at it no doubt.
I don't want to screw this up, just get it fixed & ride. And how do I find those posts on the "old" site, that I have not ever seen.
New to the site & tried to get in to it for years. Weird.
Sounds like you got it going without too much drama after Steve's post, but I would sure like to find the old site & those posts.

I found this:
**************************
Hi Steve,

Yes, That's exactly what I did. Prised everything off! Found a couple of posts on the old web site and thats how they said to change the oil seal, and then the discussion went onto changing the oil, as though thats alll there was to it... But as I've found, It's not that simple. I can't see how to get the oil out. Whats the other alternative... the one you have kind of mentioned. It sounds a bit more methodical and probably makes more sense. Please explain.
************************
In this thread:
http://www.carpe-tdm...6164

I also ask for help here:
http://www.carpe-tdm...findpost&p=8357

Thanks.
Signed, Anxious in Anchorage.

Edited by Tom S, 19 June 2006 - 10:29 am.


#16 wicklamulla

wicklamulla

    is it Jizzy Rascal time yet.....?

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 12,211 posts
  • Location:Parish of Cruwys (pronounced 'Cruise' just loike Tom) Morchard, Mid Devon.
  • TDM model: 1999

Posted 19 June 2006 - 12:53 pm

welcome Tom S thats a fine looking MKI and the best colour to boot (which incidentally you seem to be doing in yer picture!!)

spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.

I loike tay and hang sangwiches !

www.kenhogantreeservices.co.uk

http://s33.photobuck...77/wickla/?sc=6



http://reg.imageshack.us/v_images.php

post-1-1150550733.gifpost-1-1150550726.gifpost-1-1150559830.gif


#17 Tom S

Tom S

    enuff posts to fill a 50cc

  • Member
  • 55 posts
  • Location:Anchorage Alaska
  • TDM model: 1992

Posted 19 June 2006 - 02:39 pm

QUOTE(wicklamulla @ Mon 19th Jun 2006, 04:38 AM) <{POST_SNAPBACK}>
welcome Tom S thats a fine looking MKI and the best colour to boot (which incidentally you seem to be doing in yer picture!!)

Thanks for the welcome Wicky.
No, I wouldn't boot the thing over, just an old phart trying to climb on. There have been times---
But then I would just have more work to do to fix it. Been a good bike. From experience I expect that from a "Ya-Mama!"
Now I got the dust cover & the cheap, round, rusty little clip out, it looks like a pain to dig out that seal like I assume 'Plug' did.
It is quite recessed down in there. My old eyeballs ain't that good sometimes either.
Need to keep debris out of the oil. Trying to keep it simple. Need my SUV bike NOW!
Don't want to be (thanks / apology to Pete Townsend, R Daltery & The Who) 'FORKED AGAIN!' by my own doing.
So, how are your forking adventures going there Wick? Any tips?
Fork!

Edited by Tom S, 19 June 2006 - 03:12 pm.


#18 wicklamulla

wicklamulla

    is it Jizzy Rascal time yet.....?

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 12,211 posts
  • Location:Parish of Cruwys (pronounced 'Cruise' just loike Tom) Morchard, Mid Devon.
  • TDM model: 1999

Posted 19 June 2006 - 03:40 pm

well Tom i have a 99 mkII so i tink it's prolly easier to strip/rebuild the forks on these than MKI's. earlier on this year i emptied the fork oil and washed out the forks and fitted stiffer springs with heavier 15wt oil. i have not actually rebuilt any TDM forks before so i dunno how difficult it is to replace the bushes, hedges, forests & seals etc etc. apparently the MKI's "have better" cartridge type forks over the MKII's cheaper type, but im not sure on this. there is loads of info on the fork rebuilds and im sure you have read Stinkfoots recent exploits on the same. good luck WiCk

spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.

I loike tay and hang sangwiches !

www.kenhogantreeservices.co.uk

http://s33.photobuck...77/wickla/?sc=6



http://reg.imageshack.us/v_images.php

post-1-1150550733.gifpost-1-1150550726.gifpost-1-1150559830.gif


#19 dapleb

dapleb

    Monkey Boy

  • Root Admin(A)
  • PipPipPipPipPipPipPipPip
  • 18,197 posts
  • Location:The home of morris dancin
  • TDM model: 1990

Posted 19 June 2006 - 06:10 pm

Welcome Tom:

Q1: Yes
Q2: If you can find a method please let us know. The smaller bush (top bush) is probably reuseable but the bottom one is destroyed as the forks are seperated and the two collide. Haynes suggests that they just rest against each other, but what actually happens is the top bush rides over the bottom bush and detroys the teflon surface.
Q3:Have not needed any special tools to dismanlte. There is a pic of the components shown above. If you want detailed pics of anything particular lettuce snow.

Cheers
dapleb
"Whats up", "Piston Broke", "Yeah me too...hic"

If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117

Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.

Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.

#20 stevepsd

stevepsd

    seems to like Carpe

  • Members
  • 71 posts
  • TDM model: 1992

Posted 19 June 2006 - 07:14 pm

Hi Tom,

A TDM in Alaksa, great! I've been up in your neck of the woods (Anchorage, Kodiak, King Salmon, Cordova) over the past couple of years - just getting ready to be up there next month. I like the summers, but the winters are not that bad - now Fairbanks is probably another story!

To change the fork seal, remove the cap, spring, and adjusting rod. Pour out the old oil, then remove the bottom bolt, a air wrench will spin the bolt off without having to fab a holder for the damping rod. Remove the oil seal dust cap and retaining clip.

Secure the fork leg in a vise, grap the fork tube, and pull up sharply, repeatly (like a slide hammer) to remove the fork tube from the leg. The fork bushings (#14 & #16) will usually be ruined when doing this. Replace them along with the fork seal. This is the only way, unless you can fab up a real thin and strong flat hook to slide between the fork tube and the seal lip to pry the seal out in-stu.

Depending on how many miles on the bike, it might be time to relace the fork bushings anyway, as they do wear, especially if you ride alot on the 'normal' Alaska gravel roads.

Hope this helps.

-steve
'92 TDM850 Corbin Seat, Stainless Laser Pro-Stock Exhaust, K&N, Ceramic Coated downpipes, BMW F650
Handguards, MRA TouringScreen Windshield, dual-FIAMM's, Euro city light, YZF-R6 electric fuel
pump & polished rims!
'87 XR600R To many mods to list, but it's street legal (sort-of)!
'82 XJ550 Seca


0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users